Colour is the first thing anyone notices about a brick wall, and mortar is roughly 17% of its face. Get the colour right and the brick does what the architect drew. Get it wrong — patchy, chalky, three shades across four weeks of laying — and no amount of good brickwork saves it.
T
hat gap is why we built the bagged range. Today we’re launching Mercol’s 20kg premixed mortar in 38 colours, every one of them certified to AS 3700 Class M4, and every one of them mixed in a state-of-the-art manufacturing facility.
The problem with coloured mortar on site
Most coloured mortar in Australia is still made the same way it was thirty years ago: five shovelfuls of sand, a shovelful of cement, a shovelful of lime and a scoop of oxide, and a labourer’s memory of how much went in yesterday.
It works, until it doesn’t. Oxide dosing drifts between batches. Sand from a different pile changes the base tone before the pigment does anything. Water content shifts the cured shade. The wall reads fine while it’s wet and then dries into stripes — and by then you’re looking at grinding out joints and repointing, or living with it.
Factory-batched coloured mortar removes the on-site variables. Every 20kg bag of Mercol coloured mortar is meticulously measured and mixed, from the same double washed sand, in the same manufacturing facility. Bag one and bag four hundred lay up the same.
38 colours, one specification
The range runs the full spread — warm sandstones and buffs, the off-whites and bone tones that suit a lighter face brick, glowing reds, the mid and deep greys that carry most contemporary work, and the true darks.
What matters more than the count of colours however is what sits behind it: the AS 3700 Class M4 certification covers the entire bagged range.
That’s worth pausing on. M4 is the highest durability classification in AS 3700 — the class specified for the conditions that punish mortar hardest, including below-DPC work in aggressive soils and severe marine exposure. With Mercol, you can rest assured that your colour decision won’t have any impact on the strength of the finished product.
Introducing Absolute Black
Ask for black mortar in Australia and what you’ll usually get is charcoal. It looks black on the pallet, goes down looking black, and cures to a soft dark grey that reads flat against a dark brick or a black-framed window.
Absolute Black is the blackest mortar available on the Australian market. It’s a genuinely black joint — dense, saturated, and stable through curing rather than fading toward grey over the first few months. Against a charcoal or manganese brick, a black steel window frame, or the dark-on-dark palettes that keep turning up in high-end residential, it does what the render shows and what charcoal never quite manages.
It’s a premium product and priced as one. If you’re specifying a black joint on a project where the joint is the design, it’s the one to look at.
Designed by a bricklayer, not a chemist
Our Mercol pre-mixed dry mortar has been developed and refined by a qualified bricklayer — someone whose test for a mortar isn’t a data sheet, it’s a full day on the boards.
That shows up in the things that don’t appear in a specification: how the mortar sits on the trowel, how cleanly it rolls onto the brick, how long the board stays workable, how little it drops down the face of the wall. Workability isn’t a soft metric — it’s laying speed, joint consistency and clean-up time, which are ultimately about saving money.
Consistency is the other half of it. Because the range is plant-batched to a fixed formula rather than mixed to a rule of thumb, the mortar behaves the same on Tuesday as it did on Friday. Crews stop recalibrating and start laying.
Independently tested
We don’t ask anyone to take our word for the performance. The range has been independently tested for compressive strength, with results verified outside the business rather than measured in-house and self-reported.
Combined with the AS 3700 Class M4 certification across the range, that gives specifiers, builders and certifiers a straightforward paper trail — one that holds up under scrutiny on projects where someone will ask for it.
Where the bagged range fits
The bagged range is an extension of our product range and sits alongside our automated silo systems. A silo is still the right answer for volume — big residential estates, large commercial builds, anywhere the brick count justifies the set-up.
Bagged 20kg is built for the jobs a silo can’t serve well:
- Precise masonry and feature work, where colour matching matters
- Luxury residential, where the joint is a design element and the tolerance for variation is nil
- Repairs, extensions and heritage matching, where you need a specific colour in a manageable quantity
- Tight-footprint sites — inner-suburban infill, restricted access, no room for a silo
Same manufacturing standard either way. Different delivery format for a different job.
Available now across the East Coast
The full 38-colour range including our newest colour – Absolute Black are available now, delivered across Victoria, New South Wales, South Australia and Queensland.
Chat to our team about your next project or to order a sample.




